In order to re-enter normal operational model, simply remove and replace power to the device. Reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. Press the Action Menu button and select DFU. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Press the Action Menu button and select Lock. Submit a valid PIN to reset the settings for your beacon to factory defaults. Reset the device to the original factory settings. Press the Action Menu button and select Reset. Submit a new and existing PIN to update the PIN for your beacon. Press the Action Menu button and select Update PIN. Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Press the Action Menu button and select Range. Update the measured power value with the results of your calibration activity and update your settings. Press the Action Menu button and select Calibrate.Ĭalibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Submit a valid PIN to update the settings for this beacon. Press the Action Menu button and select Apply. Select any RadBeacon in the table to view it's detailed settings. Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by swiping down on the RadBeacons table. It’s the perfect beacon for conferences, trade shows, exhibits and other events where power may not be readily available and. Once discovered, you can display each beacon's operating settings and make modifications to those settings. RadBeacon Dot is a fully standalone Bluetooth Smart proximity beacon using iBeacon, AltBeacon and Eddystone technology, implemented in a lightweight package that is powered by a battery. With the RadBeacon app you can scan for nearby configurable Radius Networks beacons. The RadBeacon app from Radius Networks requires an iOS iPhone, iPad or iPod touch running iOS 7.1 or higher and equipped with Bluetooth 4.0 capabilities. First make sure you beacons are in configurable mode.The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services as well as other emerging proximity services. Unfortunately, iOS blocks reading identifiers of iBeacon packets unless you know the Proximity UUID up front. For details see "How do I put beacons into configurable mode?" This can be done by power cycling the beacon. In order to start scanning for beacons, first launch the RadBeacon configuration app. The main beacon scan screen is displayed which should be empty. To start scanning for beacons, press the SCAN button in the upper right corner on the action bar. This scans for beacons for 5 seconds and displays all beacons found during the scan. Potentially configurable Eddystone RadBeacons should be identified in the list with the Bluetooth device name "RadBeacon G". Tap on the beacon you would like to configure. If it is configurable, then the configuration detail screen for the beacon is displayed. If it is not configurable, an alert is displayed after 15 seconds indicating that the beacon could not be contacted for configuration. Occasionally, a configurable beacon cannot be contacted by the app on the first attempt, so you may need to try again. The RadBeacon USB Eddystone beacon can be configured to advertise any combination of iBeacon, AltBeacon, Eddystone UID, and Eddystone URL (although you must choose at least one). The RadBeacon Dot Eddystone beacon can be configured to advertise iBeacon/AltBeacon and either Eddystone UID or Eddystone URL. If you configure a URL to be broadcast, then it will broadcast iBeacon/AltBeacon and Eddystone URL. If you leave the URL blank, then it will broadcast iBeacon/Altbeacon and Eddystone UID. The Eddystone namespace ID cannot be entered directly in the RadBeacon configuration app.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |